Caning & Rattan: Recognising Quality and Caring for a Woven Seat
Caning and rattan run through the history of furniture, from the nineteenth-century Thonet chair to the modernist seating of the twentieth. Light and supple, they let air through and contrast with metal and solid wood. A woven seat in good condition is sought after; a damaged one often puts buyers off for no good reason, because caning can be redone. Here is how to recognise these materials, judge a weave and look after it.
Rattan, cane, reed: the right words
Rattan is a tropical climbing palm whose stem, once harvested and worked, yields several materials. The whole stem, steam-bent, is used to make structures and chair frames: this is rattan in the sense of rattan furniture. The outer bark, cut into fine strips, gives the cane (or "rattan cane") used for woven caning. The inner pith yields reed, used in basketry.
In design furniture, both registers appear: armchairs whose entire structure is bent rattan, and wood or metal seats whose seat or back receives woven caning. Some manufactured pieces, at Cassina for instance, combine a rigid frame with a cane panel, which demands precise, taut weaving.
Hand caning or machine caning
This is the line between craft work and mass production. Traditional hand caning is done strand by strand, through holes drilled in the frame, following a hexagonal pattern built up in several crossing passes. This lengthy work gives a regular, taut weave whose strands visibly pass through the frame holes. It is the mark of a quality seat, repairable hole by hole.
Machine caning, or sheet caning, is prefabricated as a web then set into a groove cut around the frame, where it is held by a locking strip called a spline. Faster and cheaper, it is recognised by this peripheral groove and the absence of individual holes. It is perfectly valid on many pieces, but it is replaced as a whole rather than strand by strand.
Telling one from the other is simple: look at the frame's edge. Regular drilled holes signal hand caning; a continuous groove with a spline signals sheet caning.
Recognising quality work
Three points tell you about quality. Tension first: good caning is firm and regular, without bellying or slack. Regularity of pattern next: the hexagons are crisp, aligned, without skipped strands. Edge finish finally: on hand caning, the perimeter is cleanly closed; on sheet caning, the spline is well fitted, without lifting.
The material counts too. Good-quality cane has an even natural tone, a slight sheen, a suppleness that resists without breaking. Dry, brittle or unevenly yellowed cane announces a fragile seat. On structural rattan, check that the bends are regular and that the bindings joining the elements are tight and intact.
Re-caning a seat
A damaged woven seat is not lost. Re-caning is a trade in its own right, and a seat redone by a craftsperson is fully usable again. For hand caning, the craftsperson redoes the weave strand by strand through the existing holes, which respects the original frame. For sheet caning, the old web and spline are removed, then a new web is set into the groove.
On a valuable piece, well-done re-caning is generally accepted: it makes the seat usable without touching the rest of the piece. The important thing is to entrust the work to a competent professional who will choose the right technique for the frame, and not to attempt a makeshift repair that would damage the wood.
Managing humidity
Cane and rattan are natural fibres sensitive to ambient air. Too dry, the weave becomes brittle; too humid, it moulds or slackens. The ideal is a stable indoor environment, away from direct sun which fades and dries it out.
For routine care, regular dusting is enough, with a soft brush or a low-power vacuum. Slightly slack caning can sometimes be tightened by gently dampening the underside then letting it dry flat, the weave re-tensioning as it dries; this operation calls for restraint, as excess water would do the opposite. Avoid soaking cleaning and direct heat sources. On a daily-use seat, a cushion reduces wear on the strands.
What we check
When a caned or rattan seat comes through LAPIERRE MARKET, we identify the technique (hand or sheet caning), check the tension, the pattern and the condition of the strands, then the frame and, for structural rattan, the bends and bindings. When re-caning is needed, it is entrusted to a craftsperson in the original technique. The photographs show the actual weave, and the listing for the piece describes the condition of the caning and mentions any re-caning. See also our Cassina selection.
By
LAPIERRE MARKET
